Dodge Dakota ForumDodge Dakota PhotosDodgeDakota.net Membership
  Forums   Forum Tools
20:22:06 - 11/08/2024

V8 Dakotas
FromMessage
01Dak
Dodge Dakota
JOIN HERE


6/18/2005
14:34:54

Subject: blower motor resistor location for 01
IP: Logged

Message:
My Blower Motor is only working on high. I have looked on the passanger side firewall as some threads state, but can't find it. Where is the blower motor resistor located at on the 2001 4.7L?



corjunk
Dodge Dakota
JOIN HERE


6/18/2005
17:02:11

RE: blower motor resistor location for 01
IP: Logged

Message:
it is located on the bottom of the passenger side hvac housing right beside the blower motor.it is held in by 2 screws.



01Dak
Dodge Dakota
JOIN HERE


6/20/2005
00:57:39

RE: blower motor resistor location for 01
IP: Logged

Message:
So it is located inside the cab? Not on the firewall of the engine compartment?



01dak
Dodge Dakota
JOIN HERE
 Email

6/20/2005
13:29:52

RE: blower motor resistor location for 01
IP: Logged

Message:
Yep,its in the cab. Go get the new one and take a look around. You will find it. Just replaced mine about 2 weeks ago. Costs around 15 bucks.



JimmyD
Dodge Dakota
JOIN HERE


6/20/2005
14:13:02

RE: blower motor resistor location for 01
IP: Logged

Message:
Look at the blower housing on the passenger side under the dash. You'll recognize the blower motor area right away. Go inboard just a bit and you'll see a connector going up into the plastic housing. That connector (5-wires, if I remember) is for the resistor board. Remove the two Phillips screws, and it'll come right out. A flashlight sometimes helps.




MotorSport4.7
Dodge Dakota
JOIN HERE


6/20/2005
19:23:53

RE: blower motor resistor location for 01
IP: Logged

Message:
Man this site is just awesome for help! Going to replace mine now too, I have the same problem and wasnt sure where it was



corjunk
Dodge Dakota
JOIN HERE


6/20/2005
22:57:30

RE: blower motor resistor location for 01
IP: Logged

Message:
If it blows again anytime soon you will need to replace the blower motor as well as another resistor.



MotorSport4.7
Dodge Dakota
JOIN HERE


6/21/2005
23:11:59

RE: blower motor resistor location for 01
IP: Logged

Message:
Is the blower motor resistor just a dealer part? I went to Advanced Autoparts and they didnt have it. I am wondering if AutoZone or PepBoys would have it.



JimmyD
Dodge Dakota
JOIN HERE


6/21/2005
23:28:09

RE: blower motor resistor location for 01
IP: Logged

Message:
Dealer only.
It's a special circuit board with carbon resistor tracks on it.
As corjunk stated, if it keeps blowing, that means the blower is drawing too much power and should be replaced.



heat sink it
Dodge Dakota
JOIN HERE


6/21/2005
23:31:56

RE: blower motor resistor location for 01
IP: Logged

Message:
I stuck one of those computer heat sinks on mine.
Works good.




MotorSport4.7
Dodge Dakota
JOIN HERE


6/21/2005
23:50:35

RE: blower motor resistor location for 01
IP: Logged

Message:
Thanks guys. I figure it is worth replacing once. It is only around $12 from what I hear for the resister. If it blows again, then Ill look into replacing the blower motor. How big of a project is the blower motor if it does come to that?



JimmyD
Dodge Dakota
JOIN HERE


6/21/2005
23:55:40

RE: blower motor resistor location for 01
IP: Logged

Message:
One connector kinda behind the blower, and 3 Phillips screws, all accessible from the passenger side under the dash. It'll drop right out.
Grab a flashlight and go exploring - you'll see.



MotorSport4.7
Dodge Dakota
JOIN HERE


6/22/2005
00:05:58

RE: blower motor resistor location for 01
IP: Logged

Message:
Thanks again,,,GREAT people GREAT site.



JimmyD
Dodge Dakota
JOIN HERE


6/22/2005
20:11:15

RE: blower motor resistor location for 01
IP: Logged

Message:
Coupla more things, MotorSport.
I haven't had to replace my blower (I just pull it once in a while to clear the leaves and such), so I don't know if a new motor will have the drum-shaped fan attached. If not, the fan is a friction fit on the motor shaft. It's fairly tight, but will come off with effort.
Don't run the blower with the resistor block dangling out of the housing just to see how hot it gets. I've done it. It gets real hot real fast, so needs to be screwed in place up in the air stream.



MotorSport4.7
Dodge Dakota
JOIN HERE


6/23/2005
17:16:45

RE: blower motor resistor location for 01
IP: Logged

Message:
Thanks JimmyD I'm going to take your guys advice & do it tomorrow.



MotorSport4.7
Dodge Dakota
JOIN HERE


6/25/2005
14:59:51

RE: blower motor resistor location for 01
IP: Logged

Message:
Replaced by Blow Motor Resister Yesterday and so far all is well. All speeds are working great. I noticed the old resister was all bubbled up. Looked like a bad tint job on a window. Thanks again





Mark Walker
Dodge Dakota
JOIN HERE
 Email

6/26/2005
12:00:07

RE: blower motor resistor location for 01
IP: Logged

Message:
I need some help! The connector on the engine side of the firewire that feeds the blower motor has melted down. When I hold the wire to the connection point it gets hot really fast. does anyone know if it's just that the blower is drawing too many amps, or could it be the resisters under the dash? Has anyone else run into this?



Gaston
Dodge Dakota
JOIN HERE


6/26/2005
19:51:34

RE: blower motor resistor location for 01
IP: Logged

Message:
Well, Mark.
Here's something you should remember about the way your Dakota is wired: Everything's always HOT (at 12VDC).
The switches and other controls simply supply a ground path to complete the circuit.
In the case of the blower motor, the ground path is switchable between different resistances, which is what gives the multiple fan speeds.
Knowing that, when you hold that wire to the connection point, 12VDC is finding a low- to no-resistance path to ground and the wire heats up.
Make these checks:
1 - find out which side has the 12V: the wire or the connection point.
2 - make sure fan control on dashboard is OFF.
Hold the wire to the connection point. Still getting hot?
3 - disconnect the fan motor connector that's under the dash, as described in one of the posts above. Hold the wire to the connection point. Still getting hot?




Ross T
Dodge Dakota
JOIN HERE


7/20/2005
08:03:42

RE: blower motor resistor location for 01
IP: Logged

Message:
2001 QC Sport: Replaced resistor block last night. $11.50 and 10 minutes worth of work. The dealer said 1 hour - screw them. Used this sight to find others with similar problem. Here's a tip - loosen the screw holding the ductwork just below where the resistor block goes, and then pull the ductwork down. This allowed easy access to both screws (5/16 hex). Remove the connector after you drop the resistor block. Slide the little red locking mechanism out and the connecter disconnects easily.



TVB
Dodge Dakota
JOIN HERE
 Email

8/09/2005
10:33:55

RE: blower motor resistor location for 01
IP: Logged

Message:
Thanks for the info, I will be replacing mine when I get home tonight. This seems like a common problem. Great site.



Andy01
Dodge Dakota
JOIN HERE
 Email

8/13/2005
13:40:04

RE: blower motor resistor location for 01
IP: Logged

Message:
Just replaced mine today, easy job, good suggestion to buy part first so you know what you're changing. P/N has changed WAS: 4885635AC - NOW: 5174618AA. Old part made in Mexico, new one made in USA. Cost $9.45 w/tax $10.02.

Easier to get to the left hand screw if you drop the heat duct down. Two 5/16 hex head screws hold it up - I just loosened the one closest to the firewall. Total time was about 45 minutes and that included the trip to get the part at the dealership parts counter.

Big thankyou to contributers to this site, it helped a lot.

Andy
01 4.7L Dakota Sport



   P 1 Next Page>>


 



Home | Forums | Members | Pictures | Contact Us

This site is in no way affiliated with Chrysler or any of its subsidiaries.