Dodge Dakota ForumDodge Dakota PhotosDodgeDakota.net Membership
  Forums   Forum Tools
12:06:31 - 04/20/2024

Dakota Performance
FromMessage
Martin
GenII
 Email User Profile


10/02/2005
16:37:25

Subject: Manual Rack & pinion For Gen II?
IP: Logged

Message:
Does anybody know if any 2wd gen II dakotas came with manual rack and pinion steering? Or if the gen 1 did and it would fit in a gen II?

Check out my four banger Dak at www.cardomain.com/ride/2020301

.boB
Dodge Dakota
JOIN HERE


10/02/2005
23:42:44

RE: Manual Rack & pinion For Gen II?
IP: Logged

Message:
I am guessing that you're trying to save weight, and/or trying to free up some HP.

You can use the stock power rack. Remove the lines, and replace the with a cap. Be sure adrill a very small hole in the cap to allow air to move in and out.

Of course, this hole may be a problem of you drive in the rain/mud/water a lot. Then you can put a nipple on the cap, and run a vacume line up under the hood and connect it to a small filter, just like on a front differential.




Opie
Dodge Dakota
JOIN HERE


10/03/2005
00:34:46

RE: Manual Rack & pinion For Gen II?
IP: Logged

Message:
Except you'd be dripping fluid every time you turned and you would leave puddles where you park and it would go dry and start rusting and making noise and would be harder to turn and make your arms sore and maybe you would wreck your truck so you probably better not do it.



outdoorsman
Dodge Dakota
JOIN HERE


10/03/2005
08:47:43

RE: Manual Rack & pinion For Gen II?
IP: Logged

Message:
im also interested. would be a good mod.



Martin
GenII
 Email User Profile


10/03/2005
17:03:21

RE: Manual Rack & pinion For Gen II?
IP: Logged

Message:
No I just don't want to cut the lines off and cap them. I knew I should of stated that first thing.

Check out my four banger Dak at www.cardomain.com/ride/2020301

E 101
Dodge Dakota
JOIN HERE


10/03/2005
18:28:14

RE: Manual Rack & pinion For Gen II?
IP: Logged

Message:
"I knew I should of stated that first thing."

No you moron. It's:
I knew I should have stated that first thing.



intensedak39
*GenIII*
 User Profile


10/03/2005
20:37:30

RE: Manual Rack & pinion For Gen II?
IP: Logged

Message:
a power steering rack without the pump is a whole lot harder to turn than a manual rack.. i konw, i did what .boB said to do... but us genIII's dont have a manual rack option, so i did what i had to.



Old Fool
Dodge Dakota
JOIN HERE


10/03/2005
21:02:36

RE: Manual Rack & pinion For Gen II?
IP: Logged

Message:
Greg = Wimp

Just don't turn while sitting dead still, get some motion and then start turning if you must turn.

Heidts has some great manual units that will bolt right on in place of the stock power units.
Heidts Steering Components

Their base manual rack and pinion set up will bolt right in place of the Dakota Power Unit.

I'm an Authorized Heidts Dealer here in South Texas.

Later,



intensedak39
*GenIII*
 User Profile


10/03/2005
21:06:17

RE: Manual Rack & pinion For Gen II?
IP: Logged

Message:
lynn

yeah yeah i know i am a wimp.. but i havent had power steering in two years!! haha!!






GraphiteDak
GenIII
 Email User Profile


10/04/2005
00:25:10

RE: Manual Rack & pinion For Gen II?
IP: Logged

Message:
Hmm. Thanks for the link. I'll keep that in mind when I need that Rack and Pinion for my Duster later one :p



Martin
GenII
 Email User Profile


10/04/2005
09:48:41

RE: Manual Rack & pinion For Gen II?
IP: Logged

Message:
Thanks Old Fool I will keep Heidts in mind when its time to do the swap.
E 101 this is a Dakota forum not a grammar forum.


Check out my four banger Dak at www.cardomain.com/ride/2020301

intensedak39
*GenIII*
 User Profile


10/04/2005
14:26:14

RE: Manual Rack & pinion For Gen II?
IP: Logged

Message:
Don't worry martin, E101 needs to work on his punctuation.



Pull truck
Dodge Dakota
JOIN HERE
 Email

2/21/2021
12:04:14

RE: Manual Rack & pinion For Gen II?
IP: Logged

Message:
I have a 99 dakota 2wd that had 3.9 v-6 in it, i
built it into a 2wd pull truck and with the v-8
motor sitting as far forward as i can get it i am
looking to see if i can get manual rack n pinion
to replace the original power one with hoses
capped, with motor sitting over front it can only
be turned when in motion, so far all i can find
is power replacements.



   P 1


Post a reply to this message:

Username Registration: Optional
All visitors are allowed to post messages


Name:
Email:
Notify me when I get a reply to my message:Yes  No

Icons:            

          

Subject:
Message:
 



Home | Forums | Members | Pictures | Contact Us

This site is in no way affiliated with Chrysler or any of its subsidiaries.